ICAR AICE-JRF/SRF Dairy Processing Equipment: practice questions
ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR
Original practice questions written to the published syllabus · not past papers
10worked here, free
62written to this exam in this subject
13syllabus units
About ICAR AICE-JRF/SRF
ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.
Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.
Dairy Processing Equipment in ICAR AICE-JRF/SRF
Unit 5: dairy processing equipment, aseptic processing and packaging equipment, storage tanks (horizontal and vertical silos, insulation, nozzles and mountings), construction codes and design for heat exchangers. Unit 4: heat exchangers (LMTD, effectiveness). Expect design calculations and comparisons of equipment types.
Construction, operation, care and sizing of the machines in a milk plant: tanks, separators, homogenisers, pasteurisers, sterilisers and fillers.
Our 62 ICAR AICE-JRF/SRF questions in this subject: 7 easy, 35 medium, 20 hard, across 13 units.
10 practice questions, worked
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.
Question 1 · hard
A separator bowl spins at 6,000 rpm. At a radius of 0.25 m, roughly how many times gravity (9.81 m/s²) is the centrifugal acceleration?
About 10,061 g
About 16.0 g
About 917,431 g
About 255 g
Answer and working
A. About 10,061 g
ω = 2π × 6000 ÷ 60 = 628.3 rad/s; rω² = 0.25 × 628.3² = 98,696 m/s² ≈ 10,061 g. The other figures forget 2π, use rpm instead of rad/s, or use ω instead of ω².
Question 2 · medium
If agitator speed is doubled with the same impeller, by what factor does power rise (turbulent flow, P ∝ N³)?
What is the purpose of a silo air vent with filter?
Prevent vacuum or pressure damage
To add carbon dioxide for preservation
To cool the milk by blowing air
To let cream escape from the top
Answer and working
A. Prevent vacuum or pressure damage
Blocked vents can collapse tanks, for example when hot CIP solution cools.
Question 4 · hard
Why can an outdoor silo collapse after hot CIP if its vent is blocked?
Cooling vapour creates a vacuum
Hot solution expands the steel until it tears
Caustic dissolves the inner shell
Wind pressure acts on hot steel
Answer and working
A. Cooling vapour creates a vacuum
Contraction of hot vapour lowers internal pressure.
Question 5 · hard
Why are steam barriers fitted on valves in aseptic systems?
To remove air from the product
Keep shaft seals sterile
To cool the valve body
To heat the product further
Answer and working
B. Keep shaft seals sterile
Steam around seals blocks microbial ingress.
Question 6 · medium
Static mixers blend streams by:
Rotating blades driven by a motor
Fixed elements dividing the flow
Heating the stream
Vibrating the pipe
Answer and working
B. Fixed elements dividing the flow
Fixed elements split and recombine the flow, so no moving parts are needed.
Question 7 · medium
In continuous butter makers, butter grains form in:
A vacuum pan
A slowly rotating drum over hours
A high-speed beater cylinder
A spray chamber
Answer and working
C. A high-speed beater cylinder
Grains form within seconds.
Question 8 · medium
The vacuum section of a continuous butter maker:
Adds air for overrun like ice cream
Heats the butter
Separates buttermilk
Removes air for a denser butter
Answer and working
D. Removes air for a denser butter
Air removal improves body and keeping quality.
Question 9 · medium
Pasta filata curd is worked in:
Pneumatic tunnel presses
Brine tanks
Pre-pressing columns
Cooker-stretchers
Answer and working
D. Cooker-stretchers
Augers knead curd in hot water.
Question 10 · medium
Why is the filling zone treated as a high-hygiene area?
Fillers heat the product to sterilise it
Product is exposed after its last heat treatment
Fillers need no cleaning
Packaging needs warm air
Answer and working
B. Product is exposed after its last heat treatment
Post-process contamination is the main risk.
A study plan for Dairy Processing Equipment in ICAR AICE-JRF/SRF
This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.
First, the heavy units (47% of the 62 questions): Sanitary design features and materials of dairy equipment (7, 11%); Retorts and in-container sterilisers (6, 10%); UHT plants: direct steam injection and infusion; indirect systems (6, 10%); Centrifugal separators and clarifiers (5, 8%); Homogenisers: triplex pump, valves, two-stage operation, care (5, 8%).
Read the manual chapters for these first and do every worked question you can find on them.
Then the middle band: Mixing and agitation equipment (5, 8%); Plate heat exchangers: regeneration, holding tube, flow diversion valve (5, 8%); Butter churns and continuous butter makers (4, 6%); Cheese vats, curd makers and moulding systems (4, 6%); Filling and packaging machines (4, 6%).
Aim for one sitting per unit, then mixed questions across them.
Then the lighter units: Milk storage tanks and silos (4, 6%); Tubular and scraped-surface heat exchangers (4, 6%); Ice cream freezers (3, 5%).
Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.
Leave time for the hard ones: Centrifugal separators and clarifiers (2 hard of 5), Homogenisers: triplex pump, valves, two-stage operation, care (2 hard of 5), Mixing and agitation equipment (2 hard of 5).
Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.
Bank the easy marks: UHT plants: direct steam injection and infusion; indirect systems (2 easy of 6); Milk storage tanks and silos (1 easy of 4).
Do these early in revision so they are fast on the day.
Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.