LAISHA
Open Laisha

ICAR AICE-JRF/SRF Cleaning-in-Place, Sanitation & Hygienic Design: practice questions

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering · India · NTA for ICAR

Original practice questions written to the published syllabus · not past papers
10worked here, free
67written to this exam in this subject
10syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD): Dairy Chemistry, Dairy Microbiology, Dairy Technology, Dairy Engineering is a PhD, fellowship and lectureship exam run by NTA for ICAR, for candidates in India.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Cleaning-in-Place, Sanitation & Hygienic Design in ICAR AICE-JRF/SRF

Unit 3: current trends in cleaning and sanitisation of dairy equipment, automation, ultrasonic techniques, biofilms, bio-detergents, innovations in sanitisers, mechanism of fouling and soil removal, assessing cleaning and sanitisation effectiveness, water conservation. Expect mechanism questions (type A and B fouling, Sinner's circle, biofilm resistance) and comparisons of sanitisers.

How dairy plants are cleaned and sanitised: fouling chemistry, detergents, sanitisers, CIP design and verification, and hygienic equipment design.

Our 67 ICAR AICE-JRF/SRF questions in this subject: 6 easy, 42 medium, 19 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

A CIP pump delivers 20 m³/h through a 50.8 mm internal diameter line. What is the flow velocity, and does it meet a 1.5 m/s target?

  1. 1.37 m/s, which just meets it
  2. 0.69 m/s, which falls short
  3. 9,868 m/s, far too fast
  4. 2.74 m/s, which meets it
Answer and working

D. 2.74 m/s, which meets it

v = (20 ÷ 3,600) ÷ (π × 0.0508² ÷ 4) = 2.74 m/s, above 1.5 m/s. The others forget the ÷4 in the area, the hour conversion, or halve the result.

Question 2 · hard

How much 1.75% available-iodine iodophor concentrate is needed for 500 L of sanitiser at 25 mg/L?

  1. 714,286 g
  2. 12.5 g
  3. 714 g
  4. 0.22 g
Answer and working

C. 714 g

Iodine = 500 × 25 mg = 12.5 g; concentrate = 12.5 ÷ 0.0175 = 714 g. 12.5 g is the iodine itself; the others multiply by the strength or forget mg-to-g conversion.

Question 3 · medium

Why is the pre-rinse done with cool or warm, not hot, water?

  1. Cool water dissolves fat better than hot water
  2. Hot water sterilises and wastes the detergent
  3. Hot water bakes protein soil onto surfaces
  4. Cold water removes calcium phosphate better
Answer and working

C. Hot water bakes protein soil onto surfaces

Heat can denature and fix protein residues.

Question 4 · medium

Sequestrants such as EDTA or gluconate are added to detergents to:

  1. Neutralise the caustic before discharge
  2. Sterilise the cleaned surfaces
  3. Increase foaming for better visual cleaning
  4. Prevent hardness scale
Answer and working

D. Prevent hardness scale

They bind hardness ions.

Question 5 · hard

For heavily mineral-rich (type B) deposits, a better sequence may be:

  1. Acid first, then alkali, then acid
  2. Hot water only
  3. Sanitiser first, then a water rinse only
  4. Alkali only at room temperature
Answer and working

A. Acid first, then alkali, then acid

Removing the mineral layer exposes protein to alkali.

Question 6 · hard

Why is evaporator run length limited even when heat transfer is still acceptable?

  1. Detergent stocks run out after 6 hours
  2. Milk quality improves with shorter runs only
  3. The vacuum cannot be held for long
  4. Thermophiles build up
Answer and working

D. Thermophiles build up

Spore counts in powder are a key specification.

Question 7 · easy

In infant formula powder plants, dry areas are monitored especially for:

  1. Lactic acid bacteria
  2. Clostridium tyrobutyricum spores
  3. Salmonella and Cronobacter
  4. Yeasts in brine
Answer and working

C. Salmonella and Cronobacter

These pathogens survive in dry environments.

Question 8 · medium

Membrane cleaning is verified mainly by:

  1. Visual inspection of the housing
  2. The temperature of the rinse
  3. The colour of the permeate
  4. Clean water flux recovery
Answer and working

D. Clean water flux recovery

Flux recovery shows whether fouling was removed.

Question 9 · medium

A limitation of ATP tests is that they:

  1. Take several days to give any result
  2. Do not identify specific micro-organisms
  3. Cannot detect food residues
  4. Need a culture incubator
Answer and working

B. Do not identify specific micro-organisms

Swabs and cultures identify organisms.

Question 10 · medium

EHEDG certifies equipment based on:

  1. Cleanability testing
  2. Energy rating
  3. Sales volume
  4. Colour of paint
Answer and working

A. Cleanability testing

Equipment is tested for in-place cleanability.

A study plan for Cleaning-in-Place, Sanitation & Hygienic Design in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (49% of the 67 questions): CIP circuit design and flow velocity (10, 15%); Detergents: alkalis, acids, sequestrants and surfactants (8, 12%); Sanitisers: heat, chlorine, iodophors, quaternary ammonium, peracetic acid (8, 12%); CIP systems: single-use, re-use and multi-tank (7, 10%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Biofilm control (6, 9%); Fouling and soil types in dairy plants (6, 9%); Hygienic design principles and 3-A and EHEDG guidance (6, 9%); Mechanism of soil removal: time, temperature, chemistry, mechanical action (6, 9%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Cleaning of membranes, evaporators and dryers (5, 7%); Verification: ATP, swabs and visual inspection (5, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Verification: ATP, swabs and visual inspection (2 hard of 5), Sanitisers: heat, chlorine, iodophors, quaternary ammonium, peracetic acid (3 hard of 8), Biofilm control (2 hard of 6).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Cleaning of membranes, evaporators and dryers (1 easy of 5); Biofilm control (1 easy of 6).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Cleaning-in-Place, Sanitation & Hygienic Design

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.