LAISHA
Open Laisha

ICAR AICE-JRF/SRF Mathematics for Food Science & Engineering: practice questions

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering · India · ICAR through the National Testing Agency

Original practice questions written to the published syllabus · not past papers
10worked here, free
15written to this exam in this subject
10syllabus units

About ICAR AICE-JRF/SRF

ICAR AICE-JRF/SRF (PhD) — Food Processing Technology, Food Safety & Quality, Processing and Food Engineering is a PhD, fellowship and lectureship exam run by ICAR through the National Testing Agency, for candidates in India. Computer-based, multiple choice.

Source: icar.org.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Mathematics for Food Science & Engineering in ICAR AICE-JRF/SRF

The calculus, linear algebra, differential equations and numerical methods behind every food engineering calculation: heat penetration curves, drying rates, reaction kinetics and process optimisation. GATE XE makes this section compulsory for every candidate who takes the Food Technology section.

Our 15 ICAR AICE-JRF/SRF questions in this subject: 0 easy, 7 medium, 8 hard, across 10 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to ICAR AICE-JRF/SRF and are not shown on any other exam's page.

Question 1 · medium

In principal component analysis of NIR spectra, the eigenvalues of the covariance matrix are 6.0, 3.0, 0.6 and 0.4. What fraction of total variance do the first two components explain?

  1. 60%
  2. 95%
  3. 75%
  4. 90%
Answer and working

D. 90%

Total variance is the sum of the eigenvalues (the trace): 6.0 + 3.0 + 0.6 + 0.4 = 10.0. The first two explain (6.0 + 3.0)/10 = 90%. 60% counts only the first component; 75% divides 9 by 12; 95% adds the third component.

Question 2 · hard

A two-compartment model dx/dt = Ax has a coefficient matrix with eigenvalues −0.5 and −0.02 per hour. Which statement describes the long-term behaviour?

  1. Both modes decay, and the slow mode with time constant 50 h dominates late
  2. The system grows without limit because one eigenvalue is close to zero
  3. The response oscillates, because two distinct eigenvalues are present
  4. Both modes decay at the same rate, set by the mean of the eigenvalues
Answer and working

A. Both modes decay, and the slow mode with time constant 50 h dominates late

Solutions are sums of e^(λt) terms; both eigenvalues are negative and real, so both decay without oscillation. The fast mode (time constant 2 h) dies first, and the slow one with time constant 1/0.02 = 50 h controls the late response. Growth needs a positive eigenvalue, oscillation needs complex eigenvalues, and the modes decay at their own rates, not at an average.

Question 3 · medium

Why do the z-value model and the Arrhenius model of thermal death agree over a narrow temperature range but diverge over a wide one?

  1. The two models always give identical predictions, and any difference comes only from fitting error
  2. The z-value model uses absolute temperature while the Arrhenius model uses degrees Celsius throughout
  3. The Arrhenius model is a zero-order model while the z-value model is a first-order model
  4. Near a reference temperature, 1/T is close to linear in T, so the two exponentials nearly coincide
Answer and working

D. Near a reference temperature, 1/T is close to linear in T, so the two exponentials nearly coincide

Arrhenius makes ln k linear in 1/T; the z model makes log D linear in T. A first-order Taylor expansion of 1/T about a reference temperature is linear in T, so the models match locally but not over a wide range. The units are the other way round (Arrhenius needs kelvin); both describe first-order kinetics; and the predictions do diverge in principle.

Question 4 · hard

The density of a cylindrical sample is calculated as ρ = m/(πr²h). If the radius has a relative error of 1% and the mass and height are exact, what is the relative error in the density?

  1. 1%
  2. 0.5%
  3. 2%
  4. 3%
Answer and working

C. 2%

From the total differential, dρ/ρ = dm/m − 2dr/r − dh/h. The radius appears squared, so a 1% error in r gives 2% in ρ. 1% ignores the power; 0.5% halves instead of doubling; 3% adds the error as if r were cubed.

Question 5 · medium

In thermal process calculation, what does the integral of 10^((T − T_ref)/z) dt over the heating and cooling time give?

  1. The total heat supplied to the container per unit mass
  2. The z value of the target organism in the food
  3. The lethality F, as equivalent minutes at the reference temperature
  4. The decimal reduction time D at the reference temperature
Answer and working

C. The lethality F, as equivalent minutes at the reference temperature

The integrand is the lethal rate, the minutes at T_ref equivalent to one minute at T. Summing it over the process gives F (F₀ when T_ref = 121.1 °C and z = 10 °C). D and z are kinetic properties of the organism, inputs to the calculation; the integral says nothing about the heat supplied.

Question 6 · hard

Why does the semi-logarithmic heat-penetration curve of a canned food become a straight line after an initial lag?

  1. The retort temperature control switches from proportional to on-off mode once the come-up is complete
  2. The higher terms of the Fourier-series solution decay much faster, leaving only the first exponential term
  3. The thermal diffusivity of the food rises steadily as it heats, which straightens the curve
  4. Heat transfer changes from conduction to radiation once the centre passes 100 °C
Answer and working

B. The higher terms of the Fourier-series solution decay much faster, leaving only the first exponential term

The conduction solution is a series of terms decaying as exp(−λₙ²αt/L²) with λₙ rising rapidly, so after a while only the first term remains, and ln(temperature difference) falls linearly. The other explanations describe effects that do not produce the straight line and are not generally true.

Question 7 · medium

In an oscillatory rheology test a gel has storage modulus G′ = 300 Pa and loss modulus G″ = 400 Pa. What are |G*| and the character of the sample at this frequency?

  1. 500 Pa; more solid-like, since tan δ < 1
  2. 700 Pa; more liquid-like, since G″ > G′
  3. 100 Pa; more solid-like, since the difference is small
  4. 500 Pa; more liquid-like, since tan δ > 1
Answer and working

D. 500 Pa; more liquid-like, since tan δ > 1

|G*| = √(G′² + G″²) = √(300² + 400²) = 500 Pa. tan δ = G″/G′ = 1.33 > 1, so viscous behaviour dominates at this frequency. 700 Pa adds the moduli; 100 Pa subtracts them; tan δ < 1 would need G′ > G″.

Question 8 · hard

An explicit Euler scheme is used for dC/dt = −kC with k = 0.5 per minute. Above what step size does the numerical solution become unstable?

  1. 0.5 min
  2. 1 min
  3. 4 min
  4. 2 min
Answer and working

C. 4 min

Each step multiplies C by (1 − hk). Stability needs |1 − hk| < 1, i.e. h < 2/k = 2/0.5 = 4 min. 2 min is 1/k, the step at which the solution first reaches zero in one step (oscillations begin beyond it, but they still decay below 4 min); 1 min and 0.5 min are well inside the stable range.

Question 9 · hard

In the explicit finite-difference solution of the one-dimensional heat equation, which condition on the mesh Fourier number αΔt/Δx² keeps the scheme stable?

  1. It must not exceed 2
  2. It must not exceed 1/2
  3. It must exceed 1
  4. It must equal exactly 1/6
Answer and working

B. It must not exceed 1/2

For the explicit (forward-time, centred-space) scheme, stability requires αΔt/Δx² ≤ 1/2; larger time steps make the solution oscillate and grow. Exceeding 1 is unstable; 1/6 is a special value that reduces truncation error but is not the limit; 2 is far beyond the limit.

Question 10 · hard

A reaction has activation energy 80 kJ/mol. By what factor does its rate constant increase from 25 °C to 35 °C? (R = 8.314 J/(mol·K))

  1. 0.35
  2. 2.00
  3. 2.85
  4. 1.00
Answer and working

C. 2.85

k₂/k₁ = exp[(Ea/R)(1/T₁ − 1/T₂)] = exp[(80000/8.314)(1/298.15 − 1/308.15)] = 2.85. 2.00 is the rule-of-thumb Q₁₀, not a calculation; 1.00 comes from entering Ea in kJ/mol with R in J/(mol·K); 0.35 is the inverse ratio, k₁/k₂.

A study plan for Mathematics for Food Science & Engineering in ICAR AICE-JRF/SRF

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (60% of the 15 questions): Numerical integration and Euler's method for ODEs (3, 20%); Applications in food science: first-order kinetics, exponential decay and logarithmic survivor curves (2, 13%); Eigenvalues, eigenvectors and the Cayley-Hamilton theorem (2, 13%); Partial differential equations: one-dimensional heat equation and Laplace equation by separation of variables (2, 13%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Complex numbers, analytic functions and Cauchy-Riemann equations (1, 7%); Definite, improper and double integrals and their applications (1, 7%); First-order and second-order ordinary differential equations (1, 7%); Limits, continuity, mean value theorems and Taylor's theorem (1, 7%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Partial derivatives, maxima and minima and Lagrange multipliers (1, 7%); Sequences, series, power series and Fourier series (1, 7%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: Numerical integration and Euler's method for ODEs (3 hard of 3), First-order and second-order ordinary differential equations (1 hard of 1), Partial derivatives, maxima and minima and Lagrange multipliers (1 hard of 1).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — ICAR AICE-JRF/SRF Mathematics for Food Science & Engineering

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.