LAISHA
Open Laisha

GATE XE Novel & Non-thermal Food Processing Technologies: practice questions

GATE — Engineering Sciences (XE), Section G Food Technology · India · IITs and IISc on rotation (2027: IIT Madras)

Original practice questions written to the published syllabus · not past papers
10worked here, free
29written to this exam in this subject
7syllabus units

About GATE XE

GATE — Engineering Sciences (XE), Section G Food Technology is a postgraduate admission exam run by IITs and IISc on rotation (2027: IIT Madras), for candidates in India. Computer-based, 3 hours, 100 marks. MCQ, MSQ and NAT. General Aptitude is common to every GATE paper; within XE, Section A Engineering Mathematics is compulsory (stated on the 2026 XE-A syllabus) and the candidate chooses two further sections, of which G Food Technology is one. The split of marks between GA, XE-A and the two chosen sections is from Laisha's knowledge of earlier brochures and was not re-read for 2026.

Source: gate2026.iitg.ac.in.

Checked against the exam body's published information. Formats and fees change; confirm the current edition there before you book.

Novel & Non-thermal Food Processing Technologies in GATE XE

Section 3 names irradiation and hurdle technology among processing principles. Expect questions on irradiation dose ranges and purposes, units, D10 calculations, and the principles of HPP, PEF and microwave heating within hurdle-based preservation.

The newer ways to make food safe or change its structure with less heat damage: high-pressure processing, pulsed electric fields, ohmic, microwave and radio-frequency heating, irradiation, UV, cold plasma and ultrasound — their mechanisms, equipment, validation and regulatory status.

Our 29 GATE XE questions in this subject: 12 easy, 14 medium, 3 hard, across 7 units.

10 practice questions, worked

Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.

These 10 were written to GATE XE and are not shown on any other exam's page.

Question 1 · easy

The main quality reason for developing non-thermal processes is to

  1. make foods taste more cooked and caramelised
  2. keep fresh-like quality
  3. increase the energy used per kilogram
  4. lengthen processing times in every plant
Answer and working

B. keep fresh-like quality

Heat damages colour, flavour, texture and vitamins; non-thermal methods aim to avoid this while ensuring safety.

Question 2 · easy

Commercial high-pressure processing typically uses pressures of about

  1. 4–6 MPa
  2. 40–60 kPa
  3. 4,000–6,000 MPa
  4. 400–600 MPa
Answer and working

D. 400–600 MPa

Commercial HPP uses roughly 400–600 MPa held for a few minutes.

Question 3 · easy

The pressure-transmitting medium in commercial HPP vessels is usually

  1. water
  2. steam
  3. nitrogen gas
  4. vegetable oil
Answer and working

A. water

Water is nearly incompressible and safe; it surrounds the packed product in the vessel.

Question 4 · hard

A water-based product at 5 °C is pressurised to 500 MPa. Taking adiabatic heating as 3 °C per 100 MPa, its temperature under pressure is about

  1. 8 °C
  2. 1,505 °C
  3. 20 °C
  4. 50 °C
Answer and working

C. 20 °C

Rise = 3 × 500/100 = 15 °C, so 5 + 15 = 20 °C. 8 °C counts only 3 °C; 50 °C uses 10 °C per 100 MPa.

Question 5 · hard

HPP-treated low-acid products such as guacamole are still refrigerated mainly because

  1. bacterial spores survive the process
  2. pressure makes the product warm for days
  3. refrigeration is needed to keep the pressure
  4. pressure destroys all enzymes
Answer and working

A. bacterial spores survive the process

Vegetative cells are killed, but spores remain viable and could grow without refrigeration.

Question 6 · medium

A soup with conductivity 1.5 S/m is heated ohmically at 1,500 V/m (ρ = 1,050 kg/m³, cp = 3,800 J/kg K). Its heating rate is about

  1. 0.085 K/s
  2. 8.5 K/s
  3. 0.00056 K/s
  4. 0.85 K/s
Answer and working

D. 0.85 K/s

q = σE² = 1.5 × 1,500² = 3.38e+06 W/m³; dT/dt = q/(ρcp) = 0.85 K/s. 0.085 and 8.5 are factor-of-ten slips; the last uses E instead of E².

Question 7 · easy

In ohmic heating, heat is generated

  1. only at the hot metal wall
  2. inside the food by its electrical resistance
  3. by microwaves absorbed only at the surface of the food
  4. by steam condensing on the product
Answer and working

B. inside the food by its electrical resistance

Current passes through the food, heating it volumetrically (q = σE²).

Question 8 · easy

Domestic microwave ovens operate at

  1. 50 Hz
  2. 2,450 MHz
  3. 13.56 MHz
  4. 915 GHz
Answer and working

B. 2,450 MHz

2,450 MHz is standard; 915 MHz industrial; 13.56 MHz is an RF band.

Question 9 · medium

Edges and corners of rectangular ready meals overheat in microwave ovens mainly because

  1. the field concentrates there
  2. they contain more fat
  3. they are colder at the start
  4. microwaves cannot reach the centre at all
Answer and working

A. the field concentrates there

Field focusing at edges and corners causes hot spots; rounded packs reduce it.

Question 10 · medium

UV-C kills microorganisms mainly by

  1. heating cells to boiling
  2. dissolving cell walls in acid
  3. removing water from cells
  4. forming thymine dimers in DNA
Answer and working

D. forming thymine dimers in DNA

Absorption near 260 nm forms pyrimidine dimers, blocking replication.

A study plan for Novel & Non-thermal Food Processing Technologies in GATE XE

This plan follows where our questions actually fall, so the time goes where the marks are likely to be. It is our reading of the syllabus, not the exam body's weighting.

  1. First, the heavy units (55% of the 29 questions): High-pressure processing: principles, equipment and microbial inactivation (7, 24%); Food irradiation: dose, sources, effects and labelling (5, 17%); Microwave and radio-frequency heating (4, 14%).

    Read the manual chapters for these first and do every worked question you can find on them.

  2. Then the middle band: Ultraviolet light and pulsed light (4, 14%); Ohmic heating (3, 10%); Pulsed electric fields (3, 10%).

    Aim for one sitting per unit, then mixed questions across them.

  3. Then the lighter units: Why non-thermal processing: quality and consumer drivers (3, 10%).

    Learn the definitions, classifications and standard numbers; these units are more often recalled than worked.

  4. Leave time for the hard ones: High-pressure processing: principles, equipment and microbial inactivation (2 hard of 7), Ultraviolet light and pulsed light (1 hard of 4).

    Come back to these after a first pass, untimed, and read every explanation, including for the options you rejected.

  5. Bank the easy marks: Why non-thermal processing: quality and consumer drivers (2 easy of 3); Microwave and radio-frequency heating (2 easy of 4).

    Do these early in revision so they are fast on the day.

  6. Finish timed. Sit the subject as a timed set without notes, mark it, and send each wrong answer back to its unit above.

Last updated · How Laisha writes and checks its pages · Report a mistake

Ask Laisha about this

Opens Laisha's chat with your question ready to send. Sign in or start free.

Unlock every question — GATE XE Novel & Non-thermal Food Processing Technologies

US$10 a month · one price worldwide · cancel any time

  • Every practice question in this subject, with full working
  • Timed exam papers and progress by unit
  • Ask Laisha to explain any answer — up to 1,000 questions a month
Free or Smarter
FreeSmarter
Grow guides, pest pages, articlesRead allRead all
Ask Laisha5 a dayUp to 1,000 a month
Exam practiceThe sample on each pageEvery question, timed papers
Crop calendar and pest alerts—For your own fields
Calculators and tools—All
Uploads and reports—100 a month, real files
10 days free for every new account, no card.